Digitech Digitech Whammy 2 Mode Pitch Shift Effect Pedal

Presenting the 5th Generation Digitech Whammy 2 Mode Pitch Shift Effect Pedal. The legendary Whammy pedal is the premier pitch-shifting pedal for any guitarist’s board, and it only gets better with time. In addition to the classic Whammy sound, the team at Digitech have added chordal Whammy pitch-shifting and true bypass to this latest version. Whammy artists have won over 60 Grammys® using its unique pitch-shifting sound to enhance their music. Its songs echo the hallways of the Rock & Roll Hall of Fame® and generate acclaim on over 700 million albums around the world. There is no doubt why Whammy is one of the most common sights on guitarists’ pedalboards. The Whammy can bring new depth to your artistry. Turn your solo into raging, rebellious screams of tone or tame your crowd with highly expressive, ambient chordal bends. Energize your audience with a scratchy note frenzy, bring them in and out of the sound tunnel with musical bursts, or carry them through an existential exploration of full-fretboard pitch translation. The Whammy puts expression into the expression pedal. Whammy Pitch Bending Effects The latest generation of the legendary Whammy Pedal brings you the same hair-raising “dive bomb” effects, gripping pitch bends and lightning harmony shifts you are looking for, plus a few new twists. Bend entire chords with the new chordal pitch shifting setting, and execute classic single note bends. Classic Whammy Interface The Whammy interface features the same legacy Whammy pitch bending options you’re accustomed to, along with some additional pitch bend settings from the Whammy DT. MIDI In for Remote Control of Whammy Effects The updated Whammy features a MIDI input for receiving incoming MIDI data. MIDI messages can select a Whammy or Drop Tune effect and set whether these effects are in an active or bypassed state. MIDI CC messages can then be used to control the Whammy Expression Pedal position. Let's look at some of the switches and controls on the Whammy: Expression Pedal: This pedal is used to control the pitch bending amount of the selected Harmony, Whammy, or Detune effect. Rocking it forward (toe down) increases the amount of pitch bending while rocking it back (toe up) decreases the amount of pitch bending. Harmony and Whammy LEDs: One of these LEDs will light when a effect is selected. Harmony effects have dry signal added to the effect signal. Classic/Chords Switch: This switch toggles between the classic Whammy algorithm (Classic) and modern algorithm from the Whammy DT (Chords). The Classic setting is ideal for single note play while the Chords setting is best suited for bending of full chords. Selector Knob: This knob is used to select one of the Whammy, Harmony, or Detune effects. Detune LEDs: One of these LEDs will light when a Detune effect is selected. The Expression Pedal controls the amount of Detune signal mixed with the dry signal. Effect On/Off Switch: This switch turns the Whammy, Harmony, or Detune effect on and off. This LED lights to indicate the effect is on. When the effect is bypassed, this LED will be off. General Specifications Sample Rate: 44.1 kHz Frequency Response: 20 Hz to 20 kHz Signal to Noise Ratio: > -105 dB (A weighted); ref = max level, 22 kHz bandwidth THD: 0.004% @ 1 kHz; ref = 1 dBu w/ unity A/D Conversion: 24 bit D/A Conversion: 24 bit Power Consumption: 2.4 Watts ( Dimensions Height: 2.5" (64mm) Width: 6.5" (165mm) Depth: 7.75" (197mm) Audio Output Output Type: 1/4” Unbalanced TS Max Output Level: +10 dBu Output Impedance: 1 kΩ Audio Input Instrument Input Type: 1/4” Unbalanced TS Max Input Level: +5 dBu Input Impedance: 1 MΩ MIDI Input: 5-Pin Din